Phoenix Hydro-X Xtreme Xtractor          

Superior Water Extraction Tool

The Phoenix Hydro-X Xtractor is the most effective and efficient extraction tool on the market today. The Hydro-X Xtractor’s patented Suction Roller provides both suction and compression—forcing water to the surface then sucking the water away, not allowing the water to be reabsorbed back into the carpet and pad. No other extractor today can pull as much water from the carpet and pad as the Hydro-X Xtractor.

The Hydro-X Xtractor is steerable and self-propelled with variable speeds. One restoration technician can operate the unit and dry a 1200 sq. ft. structure with carpet and pad in under 2 hours!

Insurance companies recognize the Hydro-X as the best tool on the market and allow for "special extraction tool" rates, sometimes up to three times higher rates per sq. ft. than regular extraction tools.

Industry experts all say its easier to extract water out of a structure than it is through dehumidification and air movement. If you want to cut a DAY(S) off of your drying process, a Hydro-X Xtractor is a necessity.

The Hydro-X Xtreme Xtractor tool can be connected with the Hydro-X Vacuum Pac, other portable extractors or truckmounts. However, the SCRT W.E.T. Study showed best performance is when combined with the Hydro-X Vacuum Pac.

Not all Carpet and Pad configurations are the same.

Every specific combination of carpet and pad will require the restorer to check and determine how many passes the Hydro-X must make to dry the floor. One structure could have multiple different carpet/pad configurations; thus the restorer will have to check each one to determine the proper amount of passes.

Note: The Xtractor is to be used for ONLY carpet and pad. Running on hard surfaces (like glue-down carpet) will not allow for a proper vacuum seal and could damage the perforated roller.

Determining a plan to dry with the Xtreme Xtractor.

Observe the type of carpet and pad installed.

Next, run the Hydro-X Xtreme Xtractor about 2-3 feet into the corner and back out (making 2 passes over the wet floor). Pull back the carpet in the corner, then pull back the pad. Squeeze the pad to determine if water leaks from your fist. If no water drips, then that is the amount of passes needed to dry this particular carpet and pad combination. If water drips from your hand after grabbing the pad, then continue running the Hydro-X into the corner until the correct amount of passes is determined to dry the floor.

Note: The speed dial on the Hydro-X can be turned up to help reduce the amount of time it takes to complete the drying process. The speed has a direct effect on the amount of water extracted in one pass. Historically, fast speed is appropriate for easy extraction type carpets and pad, such as cutpile, and slow speed is appropriate for hard extraction type carpets and pad, such as berbers.

 

Features

• Patented suction roller
• Self-propelled with positive chain drive—no belts to break or adjust
• Variable speed for every carpet and pad condition
• Extracts in both forward and reverse
• Rust and corrosion resistant stainless steel construction
• Built to withstand daily use
• Heavy duty electricals
• One year warranty on parts and labor

Phoenix Hydro-X Xtreme Xtractor Specifications
 

Part No.:	4025600
Power:	2.5 amps; 110-120 VAC grounded
Speed:	0 - 28 FPM Either forward or reverse
Warranty:	One year 100% Parts and Labor

Dimensions
 

	Machine	Shipping
Width:	17" (Base)	27-1/2"
Height:	52"	45-1/2"
Depth:	20.5" (Base)	22"
Weight:	70 lbs	80 lbs

Popular Accessories And Replacement Filters 

4025734	Hydro-X Caddy
4025346	Hydro-X Suction Chamber Cover
4025601	Hydro-X Vac Pac